How to Choose the Right Line Painting Machine

Buy too small and you’ll fight the machine on every big job. Buy too big and you’ve tied up money in flow rate you’ll never use. The right line striper comes down to one question: what are you painting, and how much of it?

This guide breaks down our recommendations for three buyer segments: contractors and property managers, municipalities, and airports. Each has different demands, and the right machine looks different for each one.

Quick answer: Contractors and property managers should start with a single-gun striper like the Titan PowrLiner 3500 or Graco LineLazer 3400, stepping up to the two-gun Titan PowrLiner 4955 or  Graco LineLazer 130HS for larger lots. Municipalities need higher flow rates and should start at the 4955 or 130HS tier, upgrading to the Titan PowrLiner 6955 or Graco LineLazer 200HS for heavy road marking. Airports need maximum output: the PowrLiner 8955 or LineLazer 200HS at minimum, with pressurized bead and dual colour machines as the workload grows. A ride-on LineDriver or Lazy Liner attachment is recommended for municipalities and effectively required for airports.

The Four Specs That Actually Matter

Skip the marketing pages for a minute. When you compare stripers, four things decide whether a machine fits your work:

Flow rate (GPM). This is the big one. Flow rate determines how wide a tip you can run and how fast you can cover ground. Parking lot restripe work runs comfortably at under 1 GPM. Wide road markings and airport work need 2 GPM and up.

Gun count. One gun handles standard restripe work. Two guns let you spray parallel lines in a single pass: double centerlines, stall lines with a stencil gun on standby, or wide lines built from two passes at once.

Pump design. This decides your maintenance bill three years from now. Titan’s sealed hydraulic PermaStroke system, found on the PowrLiner 3500, 3500s, and 5500, has no pistons, packings, or clutch to replace and carries a lifetime fluid pump warranty. Hydraulic-drive machines like the PowrLiner 4955 series and Graco’s HS series are built for long pump life under full-time use. Direct-drive machines cost less up front but wear faster on heavy schedules.

Mobility. If your markings are spread across a site or across town, a ride-on attachment (Graco LineDriver or Titan Lazy Liner) turns walking time into riding time. On some jobs it’s a luxury. On others it’s the difference between finishing today or tomorrow.

Graco vs Titan Line Stripers: Side by Side

Short answer: Neither brand wins every job. Titan PowrLiners use a sealed hydraulic pump, and Titan backs the 3500, 3500s and 5500 with a lifetime fluid pump warranty. Graco LineLazers go deeper on technology, including auto layout, bead systems and dual colour. Match the machine to your weekly paint volume, then check which service network is closer.

The two brands overlap at every size. The table pairs the closest machines, using the specifications on each Roadly product page. Recommended weekly volumes are each manufacturer’s own figures and are not measured the same way, so treat them as a guide rather than a direct comparison.

Where the two brands are the same

• Every pair in the table uses a Honda GX gas engine, and the flow rates at each size are within a few percent of each other (0.75 vs 0.75, 1.25 vs 1.3, 2.10 vs 2.15 GPM).
• Both brands supply the machine with guns, tip and hose, so you can start striping without sourcing parts first.

Where they differ

• Pump and maintenance. Titan’s PermaStroke pump has no pistons or packings to replace and only two field-serviceable wear parts, and Titan backs the hydraulic fluid pump with a lifetime warranty on the 3500, 3500s and 5500 (manufacturer’s claim). Graco’s HS machines pair a hydraulic drive with an Endurance pump.
• Technology. Graco’s LineLazer V line adds a LiveLook display with J-Log job data, automatic guns, LazerGuide, bead systems on the Reflective series and dual colour on the 200DC. Titan’s product pages describe pump durability and the PowrCenter controls rather than automation or bead options.
• Weight at the two-gun size. The 4955 is listed at 324 lb and the 130HS at 263 lb, a 61 lb difference when you load and unload.
• Power options. The Titan 4955 converts from gas to electric without tools, which helps where gas engines are not allowed. Graco sells a separate battery-powered line, the LineLazer ES and V ES series.
• Stencil work. The Titan 3500s adds a dedicated stencil gun to the 3500 (227 lb vs 160 lb), so the line gun does not need unhooking.

Which should you choose?

• Choose Titan if you want a pump with no pistons or packings to replace (Titan’s claim) and tool-free gas-to-electric conversion on the 4955.
• Choose Graco if you stripe new construction (auto layout), need bead systems or dual colour, or want a battery-powered machine.
• At the same flow rate, either is a sound purchase. Your weekly volume and your service access matter more than the badge.

Prices change, so each product link shows the current price. Not sure which size fits your work? Browse all line painting machines or call us on 587-882-7623.

Contractors and Property Managers

Where to start: one solid gun

For parking lots, strip malls, and property maintenance work, the entry point is a professional single-gun machine. Two stand out.

The Titan PowrLiner 3500 is our pick for most buyers starting out. It uses Titan’s sealed hydraulic PermaStroke pump, which has no pistons, packings, or clutch to replace, and the fluid pump is backed by a lifetime warranty. Since the pump is the most expensive failure point on a striper, that warranty changes the long-term ownership math. The PowrLiner 3500s adds a second gun connection, which is worth the upgrade if you do stencil work: handicap symbols, arrows, lettering. Run your stripe gun on the machine and keep a stencil gun on the hose.

The Graco LineLazer 3400 is the other strong option in this class. Electronic pressure control keeps lines consistent, the controls sit right at the handlebars, and the Honda GX engine is the same dependable platform you’ll find across both brands. It’s a proven machine with wide parts availability.

Both brands are solid at this tier. The decision comes down to which features matter to you: Titan’s sealed hydraulic models for the lowest maintenance burden and pump warranty, or Graco’s lineup if you plan to grow into their layout and bead technology later.

When to step up: two-gun machines

Once you’re striping large lots regularly, or bidding work with double lines, a two-gun machine pays for itself in time saved per job. It also makes wider markings faster: crosswalk bars 600 mm and up can be sprayed with both guns working side by side instead of building the width in multiple passes.

The Titan PowrLiner 4955 runs 1.25 GPM at 3,300 PSI with a 3.5 HP Honda, and it’s built for full-time duty. The SmartArm gun mount pivots and lifts for quick line adjustments, and the adjustable DeadLock handlebars matter more than they sound when you’re behind the machine for eight hours.

The Graco LineLazer 130HS is the matching option on the Graco side: a two-gun hydraulic unit designed for consistent everyday production.

When auto guns and auto layout are worth it

If you do a lot of new construction, where the lot is bare asphalt and every line has to be laid out from scratch, the Graco LineLazer 3900 and Linelazer 5900 Auto-Layout machines earn their price. Auto-Layout II replaces the chalk line and tape measure: you put down pre-marks while you walk, the LazerGuide shows you where your line will land, and the on-board system tracks gallons and footage for job records.

If your work is mostly restripe, skip this tier. You’re following existing lines, so layout automation does nothing for you. Put the money toward a ride-on attachment instead.

Contractor add-ons

A LineDriver or Lazy Liner is the single best productivity upgrade for any contractor running big lots. A laser guide is a smart add-on for newer operators: it projects your line path ahead of the machine and builds straight-line confidence fast.

Municipalities

Municipal marking work is more varied than parking lot striping. One week it’s crosswalks and zebra bars, the next it’s centerline dividing lines, then parking stalls at the rec centre. The locations are spread across town, and many of the markings are wider and heavier than lot lines. That combination pushes municipalities toward higher flow rates and ride-on mobility from day one.

Recommended starting point

Start at the two-gun hydraulic tier: the Titan PowrLiner 4955 or Graco LineLazer 130HS. Both handle the full range of municipal marking types and have the output for wider road lines that would choke an entry-level machine.

When more flow rate is needed

Departments covering serious road footage should step up to the Titan PowrLiner 6955 (4.8 HP Honda with electric start, 2.10 GPM) or the Graco LineLazer 200HS. The extra flow rate runs bigger tips on wide markings without strain, and the electric start is a small thing your crew will appreciate every morning.

One thing municipalities generally don’t need: auto layout. Most municipal work follows existing markings or simple measured layouts, so the smart money goes to power over the 3900/5900-style layout features. A 6955 or 200HS will outwork a layout machine on typical municipal jobs.

If budget allows

The Graco LineLazer 200HS with the pressurized bead system is the nice-to-have at the top of the municipal range. Pressurized bead delivery embeds glass beads into the wet paint more consistently than gravity dispensers, which means better retroreflectivity on road markings that drivers need to see at night. It’s not required for most departments, but if your budget covers it, it’s the machine your crew won’t outgrow.

Municipal add-ons

A gravity-fed glass bead dispenser is the practical choice for departments doing reflective road markings without the budget for a pressurized system. And a LineDriver or Lazy Liner is close to mandatory: when your marking locations are spread across a city, riding between and through jobs saves hours every week.

Airports

Airport markings are big. Runway centerlines, hold position markings, taxiway edges: the line widths and total footage dwarf anything in a parking lot. That makes flow rate the first spec to look at, and mobility a close second.

Starting point

The Graco LineLazer 200HS and Titan PowrLiner 8955 are the right entry points for airport work. The 8955 brings a 5.5 HP Honda with electric start, 2.5 GPM output, and a 12-gallon hopper, so you’re not stopping to refill in the middle of a long run. Both machines are rated for exactly this kind of large-format, full-time duty.

Worthwhile upgrades

Two upgrades make sense as airport workloads grow.

The Graco LineLazer 200HS adds a pressurized bead tank, delivering consistent bead embedment at the volumes airport markings demand. Reflective performance isn’t optional on regulated airfield surfaces, and pressurized delivery is the reliable way to hit it across wide lines.

The Graco LineLazer 200DC solves a different problem: colour changes. Airfields mix yellow taxiway markings with white runway markings, and flushing a single-circuit machine between colours burns serious time. The 200DC carries two independent paint systems on one frame, so you switch colours with a control instead of a changeover. On jobs that alternate colours all shift, it’s a genuine time-saver.

Mobility is not optional here

For airports, a LineDriver or Lazy Liner is almost a requirement, not an accessory. The markings are long, and the distances between them are longer. Walking an apron between hold bars wastes hours; riding it doesn’t.

Quick Reference

Segment	Start Here	Step Up	If Budget Allows
Contractors & Property Managers	PowrLiner 3500 / 3500s or LineLazer 3400	PowrLiner 4955 or LineLazer 130HS (2-gun)	LineLazer 3900 / 5900 (new construction layout)
Municipalities	PowrLiner 4955 or LineLazer 130HS	PowrLiner 6955 or LineLazer 200HS	LineLazer 200HS with pressurized beads
Airports	LineLazer 200HS or PowrLiner 8955	LineLazer 200HS (pressurized beads)	LineLazer 200DC (dual colour)

Every machine pairs with a LineDriver or Lazy Liner. The bigger the site, the more it matters.

Frequently Asked Questions

What size line striper do I need for parking lots?

A single-gun machine like the Titan PowrLiner 3500 or Graco LineLazer 3400 handles small and medium parking lots well. Step up to a two-gun machine like the PowrLiner 4955 or LineLazer 130HS when you’re striping large lots regularly or need to spray parallel lines in one pass.

Is the Titan PowrLiner or Graco LineLazer better?

Neither brand wins every job. Titan PowrLiners use a sealed hydraulic pump, and Titan backs the 3500, 3500s and 5500 with a lifetime fluid pump warranty. Graco LineLazers go deeper on technology, including auto layout, bead systems and dual colour. Match the machine to your weekly paint volume, then check which service network is closer.

Both are solid, reputable choices used by professional crews across Canada, and neither is the wrong answer. The side-by-side table pairs the closest machines at each size.

What is the difference between the PowrLiner 3500 and the LineLazer 3400?

Both are single-gun, Honda GX120 machines with 0.75 GPM flow and a listed weight of 160 lb, so they suit the same small and medium parking lots. Titan seals the pump in a hydraulic system with a lifetime fluid pump warranty. Graco lists a 15-gallon hopper and recommends up to 250 gallons a week.

PowrLiner 4955 vs LineLazer 130HS: which should I buy?

Both are two-gun machines with a Honda GX120 engine and similar flow: 1.25 GPM on the Titan and 1.3 GPM on the Graco. Listed weights differ, 324 lb for the 4955 and 263 lb for the 130HS. The 4955 converts from gas to electric without tools, which helps where gas engines are not permitted.

Do Graco and Titan line stripers use the same engines?

Mostly. The comparable machines in the table all use Honda GX engines: the GX120 on the entry and two-gun models, the GX160 on the Titan 6955 and the GX200 on the Titan 8955 and the Graco 200HS. The difference is in the pump, the controls and the options, not the engine.

What does GPM mean on a line striper?

Gallons per minute, the machine’s maximum paint output. Higher GPM supports wider spray tips and faster striping. Under 1 GPM suits parking lots; 2 GPM and up suits road and airport markings.

Do I need auto layout?

Only if you regularly stripe new construction where lots are laid out from scratch. Auto-layout systems like those on the Graco 3900 and 5900 replace chalk lines and tape measures. For restripe work over existing lines, they add cost without adding speed.

What is a pressurized bead system?

A system that propels glass beads into wet paint under pressure instead of dropping them by gravity. The result is deeper, more consistent bead embedment and better retroreflectivity, which is why it’s standard practice for road and airport markings that must stay visible at night.

Do municipalities need glass beads on road markings?

Most road markings on travelled roadways should be beaded for night visibility. A gravity-fed dispenser covers lower-speed applications on a budget; a pressurized system like the LineLazer 200HS setup delivers the most consistent results on arterial roads.

Why do airports need such high flow rates?

Airfield markings are wide, often several times wider than a parking stall line, and the total footage per job is enormous. High flow rate lets the machine run large tips at full production speed without starving the gun or overworking the pump.

What is a dual colour line striper?

A machine like the Graco LineLazer 200DC that carries two separate paint circuits, typically white and yellow, on one frame. Operators switch colours without flushing the system, which saves significant time on airfields and road jobs that alternate colours.

Is a LineDriver worth the money?

For large lots, municipalities, and airports, yes. A ride-on attachment cuts operator fatigue, keeps travel speed consistent for even line thickness, and dramatically reduces time spent moving between markings. For small-lot contractors it’s optional; for airports it’s effectively required.

Can one machine handle both parking lots and road work?

A two-gun hydraulic machine like the PowrLiner 4955 or LineLazer 130HS covers both reasonably well. If road work is the bigger share, size up to the 6955 or 200HS so wide markings don’t push the machine to its limit.